Training HVAC Operation And Maintenance

informasi Penyedia Pelatihan dan Diklat, Penyedia Pelatihan, training dan bimtek, lembaga Pelatihan dan pendidikan sdm, Diklat Indonesia, info diklat 2021, lembaga penyedia pelatihan dan training

Training HVAC Operation And Maintenance

Training HVAC Operation And Maintenance

Training HVAC Operation And Maintenance. Heating, Ventilation and Air-Conditioning System: Operation and Maintenance, covers the fundamentals and practical applications for understanding air-conditioning systems including the operation and maintenance. The comprehensive coverage of the basic theory, latest terminology, system analysis, optimization concept, and calculation methods to make this the most complete course available today in achieving an economical system. Fundamentals of air-conditioning system give comprehensively understanding air treatment and heat transfer principle in reducing energy cost, besides essential knowledge of fluid mechanics in air conditioning system.

Those all play important role on operation and maintenance of air conditioning systems. Participating in this course, you enable to analyze and recommend the most effective solution available in air conditioning system for operation and maintenance, enable to utilize energy as possible as saving due to limited energy resources, and also you are familiar and better understanding of all aspects relate to efficient air-conditioning system in building.

Ikuti juga : training sistem hvac dan kontrol plc

MATERI

  1. Basic Theory of HVAC
    Basic Concept of HVAC
    Basics of Heat and Measurement
    Thermodynamic Properties and Process
    Psychometrics and Air Treatment
    Global Issues in Environment Unit and Conversion 
  2. Refrigeration and Refrigerants
    Montreal and Kyoto Protocol Refrigerant Types and Naming Rule for Refrigerants Refrigerant Requirements and Desirable Qualities Refrigerant Selection Suitable of Oil and Refrigerant Vapor Compression and Vapor Absorption Cycles Evaporative Cooling and Cooling Tower Storage System Water Systems and Unitary Systems
  3. Air Distribution System Unitary and Central System Single-Zone Systems Multiple-Zone Systems Terminal Reheat Systems Dual-Duct or Multi-zone System Pressure Drop in Duct System Balancing Centrifugal Fans and Their Characteristics Air Distribution in Rooms Diffusers and Induction
  4. Hydronic System
    Water and Refrigerant Piping Comparison of Water and Air as Heat-Conveying Media Heat Distribution from Hot-Water System High-Temperature Water Systems Available Pipe and Tubing Pressure Drop in Water Piping Installation Pressure Drop in Refrigerant Piping Installation Pump Characteristic and Selection
  5. Basic Automatic Controls
    Basic Electricity and Magnistism
    Introduction to Automatic Controls
    Automatic Control Components and Applications
    Troubleshooting Basic Control
  6. Safety, Tools, and Equipment General Safety Practices Tools and Equipment Fasteners Tubing and Piping Calibration Instrument General Maintenance
  7. Leak Detection, Pumping Down and Charging Dye Systems Test Pressures Methods of Testing Bubble Test Halide Torch Electronic Leak Detector System Evacuation Refrigerant Recharging Refrigerant Recovery Recycling and Reclaiming
  8. Operating Principles and Symptoms Temperature, Humidity and Air Motion Air Measurement Calculating the Operating Head Pressure Compressor Pressure Ratio Air Handling Unit Fan Coil Unit Filter Check Troubleshooting and Symptoms of System Faults Troubleshooting Refrigeration Systems Troubleshooting Hydronic Systems Troubleshooting Air Distribution Systems
  9. Service Diagnosis and Repair Definition of Reparation Replacing a Thermostatic Expansion Valve Replacing the Filter Drier Compressor Efficiency Test Water Cooled Condensers: Scale and Corrosion Compressor Motor Burn-out: System Flushing Pressure Controls Special Duct Problems and Duct Maintenance Special Piping Problems and Hydronic Maintenance.

PESERTA

  1. Technicians
  2. Mechanical and facility engineers
  3. Who responsible for operating and maintaining mechanical equipments for building
Metode Pelatihan :
  • Presentasi
  • Diskusi
  • Case Study
  • Simulation
  • Evaluation (Pre and Post Test)
  • Kunjungan/Praktek (Menyesuaikan/tentative)

Informasi Lebih Lanjut

Lokasi & InvestasiFasilitas
- Yogyakarta
(6.500.000 IDR / participant)
- Jakarta
(6.500.000 IDR / participant)
- Bandung
(6.500.000 IDR / participant)
- Bali
(7.500.000 IDR / participant)
- Surabaya
(6.000.000 IDR / participant)
- Malang
(7.000.000 IDR / participant)
- Batam
(7.500.000 IDR / participant)
- Lombok
(7.500.000 IDR / participant)
- FREE Airport pickup service
(Gratis Antar jemput Hotel/Bandara/Stasiun/Terminal)
- FREE Transporsi Peserta ke tempat pelatihan .
- Module atau Handout
- FREE Flashdisk
- Sertifikat
- FREE Bag or bagpackers (Tas Training)
- Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
- 2x Coffe Break & 1 Lunch
- FREE Souvenir Exclusive
- Training room full AC and Multimedia

Catatan
Hotel untuk pelatihan ada beberapa pilihan seperti Hotel Ibis, Hotel Aston, Hotel Amaris, Hotel Cavinton, Hotel Hyatt, Hotel Grand Aston, Novotel, Hotel Harris, Hotel 101, Hotel Grand Mercure,Ritz Carlton, Hotel Ibis Style dan masih banyak pilihan menarik lainnya.Apabila perusahaan membutuhkan paket in house training anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan. Dapatkan harga spesial untuk pengiriman minimal 3 peserta dari perusahaan yang sama.

Jadwal PelatihanOnline Training
- 8-10 Januari 2022
- 15-17 Februari 2022
- 22-24 Maret 2022
- 19-21 April 2022
- 10-12 Mei 2022
- 21-23 Juni 2022
- 19-21 Juli 2022
- 9-11 Agustus 2022
- 20-22 September 2022
- 18-20 Oktober 2022
- 8-10 November 2022
- 6-8 Desember 2022
- 27-29 Desember 2022
- Instruktur mengajar secara LIVE
Durasi 4 jam perhari selama 2 hari pelaksanaan
- Media Live training
Google Meet, Zoom atau Team link
- Harga khusus
Training yang sama diikuti oleh beberapa peserta
dari perusahaan yang sama

 

Tinggalkan Balasan

Alamat email Anda tidak akan dipublikasikan.